SqueezeCenter (SlimServer) development

» Overview   » Software projects   » Hardware projects   » Hard- and Software projects

for Logitech's / Slim Devices great network music players Transporter, Squeezebox and SLIMP3

Transporter	SLIMP3 - SB1 - SBG - SB2 - SB3	Squeezebox custom case	SLIMP3 in a tube
by Logitech / Slim Devices		by GWENDESIGN

*** You are using information and scripts on this page at your own risk. ***

*** Only works with Transporter or Squeezebox2/3 players ***

With this plugin you can turn on and off an amplifier together
with your Transporter or Squeezebox2/3.
You need a small circuit (i.e. Relay card from Conrad) connected
to the IR out jack of your Transporter or the headphone jack of
your Squeezebox2/3 and an external 12V power supply.

Circuit to switch amplifer

*** AmpSwitch compatibility ***

Version 0.2 adds a compatibility mode for the Amp Switch circuit.
Please use the Power Switch II circuit for new developement.

*** Known limitations ***

If used together with IR Blaster make sure you
have no commands set for power on/off events
in the IR Blaster web interface.

(Please read instructions at the top of the file.)

*** Only works with Transporter and Squeezebox2/3 players	*** Funktioniert nur mit Transporter und Squeezebox2/3 Playern
Version >= 3.1 adds new functionality: IR Learning and IR Repeater Version >= 4.1 adds exposure to CLI	Version >= 3.1 enthaelt neue Funktionen: IR-Learning und IR-Repeater Version >= 4.1 fuegt CLI Funktionalitaet hinzu. Versionen 4.1.1 bzw. 4.9.1 sind eingedeutscht.
This plugin adds a web interface for each SB2/3 or Transporter connected to SlimServer to take advantage of the IR Blaster / Repeater / Learning. You need an IR emitter plugged into the headphone jack of your SB2/3 or the IR out jack on Transporter.	Dieses Plugin stellt fuer jede SB2/SB3 oder den Transporter, der mit dem SqueezeCenter verbunden ist, ein Web-Interface zur Verfuegung, welches Einstellungen fuer den IR-Blaster / Learning / Repeater bereitstellt. Ein IR Emitter ist noetig, den du in den Kopfhoererausgang deiner SB2/3 oder in den IR Ausgang deines Transporters steckst.
IR emitters / IR Emitter	IR emitter jack / IR Emitter Stecker
Webpage in Classic skin
IR Learning wizard in Classic skin - learned button
It reads LIRC www.lirc.org compatible remote files. Put the remote file into the IRBlaster directory and make sure its extension is .conf	Das Plugin liest LIRC www.lirc.org kompatible Fernsteuerungs-Dateien. Die Konfigurationsdatei sollte in das IRBlaster Verzeichnis kopiert werden und die Endung .conf haben.
*** Known limitations	*** Bekannte Einschraenkungen
RC6 remotes support has not yet been tested Technics remotes support has not yet been tested Remotes not using 36kHz - 40kHz carrier frequencies cannot be learned / repeated	RC6 Fernsteuerungen wurden noch nicht getestet Technics Fernsteuerungen wurden noch nicht gestestet Fernsteuerungen, die nicht 36kHz - 40kHz Traegerfrequenzen verwenden koennen nicht verwendet werden
Date Version SlimServer Firmware Download 07/26/2008 5.4  7.1.x SB: >= 29 Transporter: all Click to download 05/31/2007 4.1.3  6.5.x SB: >= 29 Transporter: all Plugins/IRBlaster.zip 08/09/2006 3.7 6.2.x, 6.3.x >= 29 Plugins/IRBlaster.zip 10/11/2005 2.6 6.2 >= 23 Plugins/IRBlaster.zip
Description and technical background can be found here: Slim Devices Wiki	Beschreibung und technischen Hintergrund findest Du hier: Slim Devices Wiki
Please post suggestions and issues on Slim Devices forum. Thank you. forums.slimdevices.com	Bitte benutze das Forum von Slim Devices, falls Du Anregungen oder Probleme hast. Danke. forums.slimdevices.com

*** Only works with SLIMP3 players ***

The TMP 100NA/250 (Temperature sensor for i2c bus) by
Texas Instruments is connected to the i2c bus of the SLIMP3.

The Temperature SW needs a plugin and a small
change in one file, to hook into the server.

Just press and hold the brightness button to show
the temperature for a few seconds.

TMP 100	Schema

Temperature in Celsius and Fahrenheit

Changes in replacement files are marked with: # *** fm ***

(Please read instructions at the top of the file.)

*** Inputs only work with SLIMP3 players ***

The PCF8574 (Remote 8-bit I/O expander for i2c bus) by
Texas Instruments is connected to the i2c bus of the SLIMP3 / Squeezebox.

Uses callback functions to tap into SlimServer.

Each of the 8 I/Os can either be an input or an output.
Outputs can be timed or linked to power state of client.

Impuls outputs are linked to power state of client.

New: IPO - pulse at on and off events - thanks to Lars.

Hardware - Squeezebox		Hardware - SLIMP3	Schema

Setup page (OUT -> linked with power)

Status page

(Please read instructions at the top of the file.)

Copyright © 2001-2008
All Rights Reserved.

MUSIC FOR YOUR EYES
www.gwendesign.ch

Hosted by www.web4free.ch